Lenze EtherCAT Controller-based Automation Manuel d'utilisateur Page 187
- Page / 205
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Lenze · Controller-based Automation · EtherCAT® Communication Manual · DMS 6.4 EN · 04/2014 · TD17 187
12 Diagnostics
12.6 System error messages
_ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _
0x98110087 ETC_E_SOE_ERRORCODE_UNIT_UNCHANGE The unit cannot be changed.
Is not supported.
0x98110088 ETC_E_SOE_ERRORCODE_UNIT_WR_PROT The unit is currently write-protected.
Is not supported.
0x98110089 ETC_E_SOE_ERRORCODE_MIN_NOT_EXIST The minimum input value is not available.
Is not supported.
0x9811008a ETC_E_SOE_ERRORCODE_MIN_UNDERSIZE The minimum input value is too small for transmission.
Is not supported.
0x9811008b ETC_E_SOE_ERRORCODE_MIN_OVERSIZE The minimum input value is too big for transmission.
Is not supported.
0x9811008c ETC_E_SOE_ERRORCODE_MIN_UNCHANGE The minimum input value cannot be changed.
Is not supported.
0x9811008d ETC_E_SOE_ERRORCODE_MIN_WR_PROT The minimum input value is currently write-protected.
Is not supported.
0x9811008e ETC_E_SOE_ERRORCODE_MAX_NOT_EXIST The maximum input value is not available.
Is not supported.
0x9811008f ETC_E_SOE_ERRORCODE_MAX_UNDERSIZE The maximum input value is too small for transmission.
Is not supported.
0x98110090 ETC_E_SOE_ERRORCODE_MAX_OVERSIZE The maximum input value is too big for transmission.
Is not supported.
0x98110091 ETC_E_SOE_ERRORCODE_MAX_UNCHANGE The maximum input value cannot be changed.
Is not supported.
0x98110092 ETC_E_SOE_ERRORCODE_MAX_WR_PROT The maximum input value is currently write-protected.
Is not supported.
0x98110093 ETC_E_SOE_ERRORCODE_DATA_NOT_EXIST The data element is not available.
Is not supported.
0x98110094 ETC_E_SOE_ERRORCODE_DATA_UNDERSIZE The data element is too small for transmission.
Is not supported.
0x98110095 ETC_E_SOE_ERRORCODE_DATA_OVERSIZE The data element is too big for transmission.
Is not supported.
0x98110096 ETC_E_SOE_ERRORCODE_DATA_UNCHANGE The data element cannot be changed.
Is not supported.
0x98110097 ETC_E_SOE_ERRORCODE_DATA_WR_PROT The data element is currently write-protected.
Is not supported.
0x98110098 ETC_E_SOE_ERRORCODE_DATA_MIN_LIMIT The data element is smaller than the minimum input value limit.
Is not supported.
0x98110099 ETC_E_SOE_ERRORCODE_DATA_MAX_LIMIT The data element exceeds the maximum input value limit.
Is not supported.
0x9811009a ETC_E_SOE_ERRORCODE_DATA_INCOR The data element is not correct.
Is not supported.
0x9811009b ETC_E_SOE_ERRORCODE_PASWD_PROT The data element is protected by a password.
Is not supported.
0x9811009c ETC_E_SOE_ERRORCODE_TEMP_UNCHANGE The data element can currently not be changed (in AT or MDT).
Is not supported.
0x9811009d ETC_E_SOE_ERRORCODE_INVL_INDIRECT Invalid/indirect
Is not supported.
0x9811009e ETC_E_SOE_ERRORCODE_TEMP_UNCHANGE1 The data element can currently not be changed (parameter or OP mode).
Is not supported.
0x9811009f ETC_E_SOE_ERRORCODE_ALREADY_ACTIVE The command is already active.
Is not supported.
0x98110100 ETC_E_SOE_ERRORCODE_NOT_INTERRUPT The command can be interrupted.
Is not supported.
0x98110101 ETC_E_SOE_ERRORCODE_CMD_NOT_AVAIL The command is not available in this phase.
Is not supported.
0x98110102 ETC_E_SOE_ERRORCODE_CMD_NOT_AVAIL1 The command is not available (invalid parameter)
Is not supported.
0x98110103 ETC_E_SOE_ERRORCODE_DRIVE_NO The received drive number does not comply with the requested
drive number.
Is not supported.
0x98110104 ETC_E_SOE_ERRORCODE_IDN The received ID does not comply with the requested ID.
Is not supported.
0x98110105 ETC_E_SOE_ERRORCODE_FRAGMENT_LOST At least on fragment got lost.
Is not supported.
Error no.
[hex]
Designation Description
- Controller-based 1
- Automation 1
- Contents 2
- 1 About this documentation 10
- Pictograph and signal word! 12
- Danger! 13
- 1) In preparation 16
- ( 36) 17
- 4.1.2 Communication 19
- Operational 20
- Pre-Operational 20
- Safe-Operational 20
- 4.1.2.3 Working counter 23
- 4.2.1 Field devices 24
- 4.2.3 EtherCAT product codes 26
- 4.3 Lenze Engineering tools 29
- PLC State of the PLC 30
- 5Technical data 34
- ( 87) 36
- 6.1 Synchronous communication 37
- 6.2 Test of DC synchronicity 38
- »PLC Designer« online help 59
- 7 Commissioning of the system 100
- 8.1 CANopen and EtherCAT 107
- Drives 9400 108
- 8.3 EtherCAT and PROFINET 109
- • Error case: 113
- 9.2 CoE Interface 115
- ( 115) 120
- SDO Download Response 123
- 9.2.2 L_ETC_CoE_SdoRead (FB) 125
- Outputs (VAR_OUTPUT) 126
- 9.2.3 L_ETC_CoE_SdoRead4 (FB) 127
- Inputs (VAR_INPUT) 130
- 9.2.5 L_ETC_CoE_SdoWrite (FB) 131
- 9.3 Device Interface 137
- 9.3.1 ETCSlave (FB) 137
- 9.3.2 L_ETC_GetSlave (FUN) 138
- 9.3.3 L_ETC_IoControl (FUN) 139
- 9.3.4 L_IODrvEtherCAT (FB) 140
- 9.4 Diagnostic Interface 141
- 9.4.1 L_ETC_GetEmergency (FB) 141
- 9.4.4 L_ETC_ReadErrCnt (FB) 145
- 9.4.5 L_ETC_ResetErrCnt (FB) 146
- 9.5 FoE interface 147
- 9.5.1 L_ETC_FoE_Read (FB) 147
- 9.5.2 L_ETC_FoE_Write (FB) 149
- 9.6 State Machine Interface 151
- 9.7 Data types 155
- 9.7.1 L_ETC_COE_EMERGENCY 155
- 9.7.3 L_ETC_COE_FLAGS 155
- 9.7.4 L_ETC_DIAGNOSTIC 156
- 9.7.6 L_ETC_ERRORCODE 157
- 9.7.7 L_ETC_IOCTLOPARMS 157
- 9.7.8 L_ETC_LANGUAGE 157
- 9.7.9 L_ETC_SLAVE_PORTS 157
- ( 160); 160
- ( 162) 160
- How to optimise the system: 162
- 12 Diagnostics 163
- 13 Parameter reference 196
- )(('%$& 204
Produits connexes et manuels pour Équipement Lenze EtherCAT Controller-based Automation
Équipement Lenze SDSGS Manuel d'utilisateur
(40 pages)
(40 pages)
(37 pages)
Équipement Lenze M300 Manuel d'utilisateur
(48 pages)
(48 pages)
Équipement Lenze 8400 Manuel d'utilisateur
(149 pages)
(149 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.021 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels