Lenze ETC Motion Control Manuel d'utilisateur Page 99
- Page / 428
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
CNC programming
G functions
G functions individual descriptions
3
3.2
3.2.2
l
99
EDSTCXN EN 2.0
3.2.2.3 G02 Circular interpolation, clockwise, G03 Circular interpolation, counterclockwise
Definition of a circle or segment of a circle, clockwise or counterclockwise,
with linear positioning of a linear axis (helix) or expanding radius (spiral)
with additional positioning of a linear axis (conical helix).
) Note!
When correction modules are used (e.g. TRC) only the normal arc
can be programmed. The additional functions are not allowed!
G02 AXES D I J K R F E L
G03 AXES D I J K R F E L
AXES Target point coordinates of the three linear principal axes (default X,Y,Z), as
well as start or target point coordinates of the three rotative secondary
axes (default A,B,C).
D Radius change on reaching the target point
I Center coordinates of the first principal axis (X) or number of additional full
circles
J Center coordinates of the second principal axis (Y) or number of additional
full circles
K Center coordinates of the third principal axis (Z) or number of additional
full circles
R Interpolation radius
F Path speed
E, L Selection of feed speed via speed (E) and increment (L). F=E*L.
With G02/G03, the interpolation on a circular path is programmed in the
selected plane (G17, G18 or G19) (G02 clockwise, G03 counterclockwise).
) Note!
It is always necessary to select a plane; there is no standard
default setting!
To determine an arc, you need to specify three points. These are always the
arc start point and arc end point, as well as either a center or a radius. This
results in the following mandatory DIN address combinations for the
determination of an arc, depending on the plane
G17: "XY IJ" or "XY R"
G18: "ZX KI" or "ZX R"
G19: "YZ JK" or "YZ R"
The target values can be specified both in absolute dimensions and in
incremental dimensions.
Syntax
Meaning of the addresses
Explanation
- ETC Motion Control 1
- Contents i 3
- Contentsi 4
- Target group 10
- Contents 10
- Further information 10
- EDSTCXN EN 2.0 11
- EDSTCXN EN 2.0 12
- ETCHN003 13
- ETCHT000 13
- Getting started 14
- EETCN095 33
- ETCN010 ETCN009 45
- ETCNC097 71
- 3 CNC programming 87
- CNC programming 100
- 3.2.2.36 G99 Return 125
- 50 mm here 126
- G120 AXES 134
- In S0: offset = S0+Tm 158
- S0 without shift 164
- XOR(x,y) 173
- (−> P586) from 181
- Machine constants 190
- 4 Machine constants 190
- 0, /* axis interfaces */ 233
- Definitions 246
- Data block 1 246
- Verfahrtaste 258
- 110 0 100 110 0 258
- SPS-Achse am Ziel 258
- Data blocks 8 ... 14 271
- ETC−MMI−Gateway 276
- 6 ET −MMI gateway 276
- ETCN001 ETCN002 277
- 7 ETC−MMI 286
- Installing ETC−MMI 287
- W Programs W Lenze W ETC 288
- Showing a new softkey line 291
- (submenu) 291
- ETCN076 306
- Set filter 307
- ETCN077 308
- File manager 309
- Appendix 328
- SPS_EXEC 334
- PLC programming 336
- 8 PLC programming 336
- %MW1.42 ARRAY[0..1] OF BYTE 357
- %MW1.43 ARRAY[0..1] OF BYTE 357
- 10987654321 428
Commentaires sur ces manuels
Produits connexes et manuels pour Logiciel Lenze ETC Motion Control
(336 pages)
(30 pages)Brocade Communications Systems SilkWorm 3200 Handbücher
Bedienungsanleitungen und Benutzerhandbücher für Computerzubehör Brocade Communications Systems SilkWorm 3200.
Wir stellen 1 PDF-Handbücher Brocade Communications Systems SilkWorm 3200 zum kostenlosen herunterladen nach Dokumenttypen zur Verfügung Bedienungsanleitung
rasha