Lenze ETC Motion Control Manuel d'utilisateur Page 233
- Page / 428
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Machine constants
List of machine constants
4
4.16
l
233
EDSTCXN EN 2.0
10,
10,
10;
MK_SW_ENDS_MINUS −10000, /* software limit stop (+)−direction */
−10000, /* [mm], relating to basic offset */
−10000,
−10000,
−10000,
−10000;
MK_SW_ENDS_PLUS 10000, /* software limit stop (−)−direction */
10000, /* [mm], relating to basic offset */
10000,
10000,
10000,
10000;
/* −−−−−−−−−−−−−−−−− */
/* controller setting */
/* −−−−−−−−−−−−−−−−− */
MK_DRIFTABGLEICH 0, /* offset adjustment [mV] for analog */
0, /* axis interfaces */
0,
0,
0,
0;
MK_REGLER_MODE 2, /* 0 = control loop open */
2, /* 1 = reserved */
2, /* 2 = P controller */
2, /* 3 = P controller with feed−forward */
2, /* 4 = spindle */
2; /* 5 = PID controller with feed−forward */
MK_KP 1, /* KP of the P controller */
1, /* (also for synchronous control) */
1,
1,
1,
1;
MK_TV 0, /* rate time [s] for D component of */
0, /* PID controller (also for synchronous control) */
0,
0,
0,
0;
MK_TN 0, /* integral−action time [s] for integral action component of
*/
0, /* PID controller (also for synchronous control) */
- ETC Motion Control 1
- Contents i 3
- Contentsi 4
- Target group 10
- Contents 10
- Further information 10
- EDSTCXN EN 2.0 11
- EDSTCXN EN 2.0 12
- ETCHN003 13
- ETCHT000 13
- Getting started 14
- EETCN095 33
- ETCN010 ETCN009 45
- ETCNC097 71
- 3 CNC programming 87
- CNC programming 100
- 3.2.2.36 G99 Return 125
- 50 mm here 126
- G120 AXES 134
- In S0: offset = S0+Tm 158
- S0 without shift 164
- XOR(x,y) 173
- (−> P586) from 181
- Machine constants 190
- 4 Machine constants 190
- 0, /* axis interfaces */ 233
- Definitions 246
- Data block 1 246
- Verfahrtaste 258
- 110 0 100 110 0 258
- SPS-Achse am Ziel 258
- Data blocks 8 ... 14 271
- ETC−MMI−Gateway 276
- 6 ET −MMI gateway 276
- ETCN001 ETCN002 277
- 7 ETC−MMI 286
- Installing ETC−MMI 287
- W Programs W Lenze W ETC 288
- Showing a new softkey line 291
- (submenu) 291
- ETCN076 306
- Set filter 307
- ETCN077 308
- File manager 309
- Appendix 328
- SPS_EXEC 334
- PLC programming 336
- 8 PLC programming 336
- %MW1.42 ARRAY[0..1] OF BYTE 357
- %MW1.43 ARRAY[0..1] OF BYTE 357
- 10987654321 428
Commentaires sur ces manuels
Produits connexes et manuels pour Logiciel Lenze ETC Motion Control
(336 pages)
(30 pages)Brocade Communications Systems SilkWorm 3200 Handbücher
Bedienungsanleitungen und Benutzerhandbücher für Computerzubehör Brocade Communications Systems SilkWorm 3200.
Wir stellen 1 PDF-Handbücher Brocade Communications Systems SilkWorm 3200 zum kostenlosen herunterladen nach Dokumenttypen zur Verfügung Bedienungsanleitung
rasha