Lenze E94AxHE Technology Application CiA402 Device profi Manuel d'utilisateur Page 49
- Page / 232
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
EDS94TA11010xxxx EN 1.2 - 03/2010 L 49
9400 Technology applications | CiA402 device profile
Parameter setting & configuration
Device control
3.7.2.3 Enable operation
This command serves to enable the operation and stop an active quick stop again.
It is changed to the device state "Operation enabled
".
[3-4] Possible state change through "Enable operation" command
Bit pattern for "Enable operation" command in 0x6040 (control word):
Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0
Reset fault Operating mode-dependent control bits Enable
operation
Quick stop Enable voltage Switch on
0 X X X1111
From all states
Power section inhibited (pulse inhibit)
Power section enabled
1
2
0
Ready to
switch on
Not ready to
switch on
Switched
on
Operation
enabled
Fault reaction
active
Fault
active
Switch on
disabled
Quick stop
active
Power on
- L-force Runtime Software 1
- Contents 3
- 1 About this documentation 8
- About this documentation 9
- Conventions used 9
- 1.1 Conventions used 9
- Danger! 10
- 2 Short description 11
- DS402 State machine 14
- 16
- Drive initialisation 25
- Code: _______ 31
- Index 31
- 3.5.4 Object attributes 33
- Common entries 35
- 3.6.2 Motor data 40
- Device control 42
- Power on 47
- X0XX0000 55
- X0XX1000 59
- Parameter Lenze setting 61
- Factor group 65
- 3.9.1 Input and output data 74
- Input data 74
- Output data 74
- ( 82) 79
- Short overview 82
- ( 81) 83
- ( 80) 83
- CiA402 Homing method -2 84
- CiA402 Homing method -1 84
- CiA402 Homing method 01 85
- CiA402 Homing method 02 86
- CiA402 Homing method 03 87
- CiA402 Homing method 04 88
- CiA402 Homing method 05 89
- CiA402 Homing method 06 90
- CiA402 Homing method 07 91
- CiA402 Homing method 08 92
- CiA402 Homing method 09 93
- CiA402 Homing method 10 95
- CiA402 Homing method 11 96
- CiA402 Homing method 12 97
- CiA402 Homing method 13 99
- CiA402 Homing method 14 100
- Touch probe/zero pulse 100
- Reference switch 100
- CiA402 Homing method 15 101
- CiA402 Homing method 16 101
- CiA402 Homing method 17 102
- CiA402 Homing method 18 102
- CiA402 Homing method 19 103
- Homing switch 103
- CiA402 Homing method 20 104
- CiA402 Homing method 21 105
- CiA402 Homing method 22 106
- CiA402 Homing method 23 107
- CiA402 Homing method 24 108
- CiA02 homing method 25 109
- CiA402 Homing method 26 110
- CiA402 Homing method 27 111
- CiA402 Homing method 28 112
- CiA402 Homing method 29 113
- CiA402 Homing method 30 114
- CiA402 Homing method 31 115
- CiA402 Homing method 32 115
- CiA402 Homing method 33 115
- CiA402 Homing method 34 116
- CiA402 homing method 35 116
- Homing mode 118
- Grayed out = read access only 119
- Position control function 121
- Brake logic 128
- Monitoring 128
- UNSIGNED_32 VAR 131
- INTEGER_32 VAR 131
- Interpolated position mode 133
- 3.11.3 Signal flow 137
- Disable voltage 140
- Shutdown 140
- Quick stop 140
- Value Unit 141
- Data type: INTEGER_32 144
- 3.12.3 Signal flow 145
- 3.13.2 Object description 150
- 0x60FF - Target velocity 151
- Speed follower 152
- 3.14.2 Object description 157
- Power stage parameters 161
- Display area 161
- Torque follower 162
- Touch probe 167
- ( 182) 174
- ( 181) 174
- 3.21.3 CountMultiError 183
- 3.21.4 CountSingleError 183
- 3.21.5 DetectErrorLimit 183
- 3.21.6 DetectMultiError 184
- 3.21.7 DetectSingleError 184
- 3.21.8 DetectUnderVoltage 185
- 3.21.9 L_DevApplErr1 185
- 4 Step-by-step commissioning 186
- ( 188) 187
- Parameter Object Information 190
- 5 Parameter reference 191
- Cxxxxx 193
- Description 193
- Parameter 195
- Data type: _______ 195
- Index: _______ 195
- Parameter reference 199
- Parameter list 199
- Parameter list 200
- Parameter list 201
- Parameter list 202
- Parameter list 203
- Parameter list 204
- Parameter list 205
- Parameter list 206
- Parameter list 207
- Parameter list 208
- Parameter list 209
- Parameter list 210
- Parameter list 211
- Parameter list 212
- Parameter list 213
- Parameter list 214
- Parameter list 215
- Parameter list 216
- Parameter list 217
- Parameter list 218
- Parameter list 219
- Attribute table 221
- )(('%$ 230
- 109 87654321 232
Produits connexes et manuels pour Logiciel Lenze E94AxHE Technology Application CiA402 Device profi
(679 pages)
(30 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.053 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels