Lenze E94P PositionServo with MVOB Manuel d'utilisateur télécharger pdf (Page 22)

20 L PM94H201B_13xxxxxx_EN

Introduction

Table 5: Bin Location, Inputs & Index Values

Bin Location Input state INDEX Value

Bin 1 Input B1 is made 1

Bin 2 Input B2 is made 2

Bin 3 Inputs B1 and B2 are made 3

Bin 4 Input B3 is made 4

Bin 5 Inputs B1 and B3 are made 5

Bin 6 Inputs B2 and B3 are made 6

Bin 7 Inputs B1, B2 and B3 are made 7

The Main program has been modiﬁed to change the end place position based on the value of the “INDEX” variable.

;************************** Main Program **********************************

ENABLE

OUT1 = 0 ;Initialize Pick Arm - Place in Retracted Position

WAIT UNTIL IN_A4==1 ;Check Pick Arm is in Retracted Position

PROGRAM_START:

MOVEP 0 ;Move to (ABS) to Pick position

OUT1 = 1 ;Turn on output 1 to extend Pick arm

WAIT UNTIL IN_A1==1 ;Arm extends

OUT2 = 1 ;Turn on output 2 to Engage gripper

WAIT TIME 1000 ;Delay 1 sec to Pick part

OUT1 = 0 ;Turn off output 1 to Retract Pick arm

WAIT UNTIL IN_A4==0 ;Make sure Arm is retracted

IF INDEX==1 ;In this area we use the If statement to

GOTO BIN_1 ;check and see what state inputs B1, B2 & B3

ENDIF ;are in.

IF INDEX==2 ; INDEX = 1 when input B1 is made

GOTO BIN_2 ; INDEX = 2 when input B2 is made

ENDIF ; INDEX = 3 when input B1 & B2 are made.

. ; INDEX = 4 when input B3 is made

. ; INDEX = 5 when input B1 & B3 are made.

. ; INDEX = 6 when input B2 & B3 are made.

IF INDEX==7 ; INDEX = 7 when input B1, B2 & B3 are made

GOTO BIN_7 ;We can now direct the program to one of seven

ENDIF ;locations based on three inputs.

BIN_1: ;Set up for Bin 1

MOVEP 10 ;Move to Bin 1 location

GOTO PLACE_PART ;Jump to place part routine

BIN_2: ;Set up for Bin 2

MOVEP 20 ;Move to Bin 2 location

GOTO PLACE_PART ;Jump to place part routine

BIN_7: ;Set up for Bin 7

MOVEP 70 ;Move to Bin 7 location

GOTO PLACE_PART ;Jump to place part routine

PLACE_PART:

OUT1 = 1 ;Turn on output 1 to extend Pick arm

WAIT UNTIL IN_A4 == 1 ;Arm extends

OUT2 = 0 ;Turn off output 2 to Disengage gripper

WAIT TIME 1000 ;Delay 1 sec to Place part

OUT1 = 0 ;Retract Pick arm

WAIT UNTIL IN_A4 == 0 ;Arm is retracted

GOTO PROGRAM_START

END

NOTE: with all digital inputs (B1-B3) off, none of the ‘If’ statements to detect place position are true and the program

defaults to placing the part it has picked into bin location 1.

1 2 ... 17 18 19 20 21 22 23 24 25 26 27 ... 139 140

Commentaires sur ces manuels

Pas de commentaire

Lenze E94P PositionServo with MVOB Manuel d'utilisateur Page 22

Commentaires sur ces manuels

Produits connexes et manuels pour Matériel Lenze E94P PositionServo with MVOB