Lenze CANopen control technology Manuel d'utilisateur télécharger pdf (Page 91)

DMS 4.2 EN 07/2011 TD17 L 91

Control technology | CANopen communication manual

Defining the minimum cycle time of the PLC project

Optimising the system

12.4 Optimising the system

 How to optimise the system:

1. Log in and load project.

2. Check the task processing times.

3. Optimising cycle times:

• If required technologically, the cycle times of the remaining tasks with lower

priorities can be decreased.

• Condition: No task with a low priority may assign more than 60 percent of the

corresponding cycle time in its task utilisation.

1 2 ... 86 87 88 89 90 91 92 93 94 95 96 ... 104 105

PC-based Automation 1
L-force Controls 1
Contents 3
Correction 5
Task utilisation 5
DMS 4.2 EN 07/2011 TD17 L 7 7
About this documentation 9
Conventions used 9
1.2 Conventions used 9
L DMS 4.2 EN 07/2011 TD17 10
 Pictograph and signal word! 11
 Danger! 12
DMS 4.2 EN 07/2011 TD17 L 13 13
4 System bus (CAN) / CANopen 15
System bus (CAN) / CANopen 17
4.1.2 Field devices 17
MC-CAN2-001 18
DMS 4.2 EN 07/2011 TD17 L 19 19
DMS 4.2 EN 07/2011 TD17 L 21 21
CAN gateway 22
CANopen bus 22
DMS 4.2 EN 07/2011 TD17 L 23 23
DMS 4.2 EN 07/2011 TD17 L 25 25
DMS 4.2 EN 07/2011 TD17 L 27 27
DMS 4.2 EN 07/2011 TD17 L 29 29
Planning the CANopen network 31
DMS 4.2 EN 07/2011 TD17 L 35 35
7 Preparing the field devices 37
DMS 4.2 EN 07/2011 TD17 L 39 39
DMS 4.2 EN 07/2011 TD17 L 41 41
DMS 4.2 EN 07/2011 TD17 L 43 43
DMS 4.2 EN 07/2011 TD17 L 45 45
DMS 4.2 EN 07/2011 TD17 L 47 47
DMS 4.2 EN 07/2011 TD17 L 49 49
DMS 4.2 EN 07/2011 TD17 L 51 51
DMS 4.2 EN 07/2011 TD17 L 53 53
Creating a PLC program 55
4. Create a block: 55
DMS 4.2 EN 07/2011 TD17 L 57 57
DMS 4.2 EN 07/2011 TD17 L 59 59
DMS 4.2 EN 07/2011 TD17 L 61 61
( 62) 63
DMS 4.2 EN 07/2011 TD17 L 65 65
DMS 4.2 EN 07/2011 TD17 L 67 67
DMS 4.2 EN 07/2011 TD17 L 69 69
DMS 4.2 EN 07/2011 TD17 L 71 71
DMS 4.2 EN 07/2011 TD17 L 73 73
DMS 4.2 EN 07/2011 TD17 L 75 75
DMS 4.2 EN 07/2011 TD17 L 77 77
DMS 4.2 EN 07/2011 TD17 L 79 79
DMS 4.2 EN 07/2011 TD17 L 81 81
DMS 4.2 EN 07/2011 TD17 L 83 83
10 CANopen with PROFIBUS 85
DMS 4.2 EN 07/2011 TD17 L 87 87
 How to optimise the system: 91
DMS 4.2 EN 07/2011 TD17 L 93 93
DMS 4.2 EN 07/2011 TD17 L 95 95
Parameter reference 97
15 Appendix 99
DMS 4.2 EN 07/2011 TD17 L 101 101
16 Index 103
109 87654321 105

Commentaires sur ces manuels

Pas de commentaire

Lenze CANopen control technology Manuel d'utilisateur Page 91

Commentaires sur ces manuels

Produits connexes et manuels pour Matériel Lenze CANopen control technology