Lenze E94AxHE Technology Application Table positioning Manuel d'utilisateur Page 35
- Page / 50
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
EDS94TA10050xxxx EN 1.2 - 03/2010 L 35
9400 Technology applications | Table positioning
Parameter setting & configuration
Control of the program flow via predefined ports
5.11 Control of the program flow via predefined ports
For a sequence control by a higher-level control (e.g. PLC) the application is provided with
predefined ports the signals of which are linked with the setpoint and control inputs of the
application via multiplexer parameters.
Input port "LPortAxisIn1" for control and setpoint signals
Input port "LPortControl1" for control signals
The input port LPortControl1 is intended for the connection with a master control.
Element variable/data type Information/possible settings
nIn1
INT
Profile number (1 .... 75) of the profile of the profile data management to be
executed
Element variable/data type Information/possible settings
LPortControl1
WORD
Control word (bit coded)
• Bits which are not listed are not assigned with a function.
Bit 3 Activate quick stop
• The is decelerated to standstill within the deceleration time set
for the quick stop function independent of the setpoint selection.
• If the quick stop function is deactivated, the drive is led to the
selected setpoint again via the set acceleration time.
Bit 7 Reset error
• An existing error status is reset if the cause of the fault is
removed.
Bit 11 Requesting control via the basic function "Positioning"
• If no other basic function is active, the status changes to
"Positioning" and positioning can be executed via the control
inputs.
• If bit 11 is reset, an active positioning is stopped, i.e. it is changed
from the active function state "Positioning" to the basic function
" Standstill" via the function state "Stopping".
Bit 12 Start positioning/restart
• The profile with the profile number defined via nIn2 is executed.
• During an active positioning process, another profile can be
defined via nIn2 which is executed after restart (renewed state
change of bit 12 from "0" to "1").
Bit 13 Profile restart
• Profile data is read in again considering the distances already
covered.
• The positioning process interrupted before is completed.
Bit 14 Profile reset
• Profile data is read in again without considering the distances
already covered.
• The positioning process interrupted before is completed.
Bit 15 Request control via the basic function "Homing" and start reference
search in the selected homing mode (C02640).
- Ä.<oaä 1
- 1 About this documentation 5
- About this documentation 6
- Conventions used 6
- 1.1 Conventions used 6
- Danger! 7
- 2 Brief description 8
- Brief description 9
- Required license/delivery 9
- 3 Introduction 10
- 4 Application example 11
- Table positioning 12
- Basic drive functions 12
- 13
- Value Unit 15
- Basic settings 16
- 5.3.2 Traversing range 16
- ( 26) 18
- Profile data management 19
- TP window start position 21
- TP window end position 21
- "Starting profile" 25
- Brake control 34
- Signal configuration 38
- 5.14.3 ApplicationError2 41
- 5.14.4 FollowingErrorScaling 41
- 5.14.7 L_PosPositionerTable1 42
- 5.14.8 L_SdSwitchPoint1 46
- 5.14.9 LimitFollowingError1 46
- 5.14.10 LimitFollowingError2 46
- 5.14.11 MonitFollowError1 47
- 5.14.12 MonitFollowError2 47
- 5.14.13 PosStarted 48
- )(('%$ 49
Produits connexes et manuels pour Logiciel Lenze E94AxHE Technology Application Table positioning
(80 pages)
(30 pages)Brocade Communications Systems SilkWorm 3200 Handbücher
Bedienungsanleitungen und Benutzerhandbücher für Computerzubehör Brocade Communications Systems SilkWorm 3200.
Wir stellen 1 PDF-Handbücher Brocade Communications Systems SilkWorm 3200 zum kostenlosen herunterladen nach Dokumenttypen zur Verfügung Bedienungsanleitung
Commentaires sur ces manuels