Lenze Global Drive PLC Developer Studio Manuel d'utilisateur télécharger pdf (Page 88)

8.5 System error messages

Drive PLC

Appendix

8−8

DrivePLC DE 6.0

8.5.1 Overview of system error messages, error sources and reactions

System error message Possible settings/response

 Lenze setting ü setting possible

Available in

No. Display Source Meaning

Code TRIP Message Warning FAIL−

QSP

Off Drive

PLC

Servo

PLC

ECSxA

x011 OC1 MCTRL Motor cable short circuit  ü ü

x012 OC2 MCTRL Motor cable earth fault  ü ü

x015 OC5 MCTRL I x t overload  ü ü

x016 OC6 MCTRL I

x t overload (C0120)  ü

x017 OC7 MCTRL I x t warning (C0123) C0604 ü  ü ü

x018 OC8 MCTRL I

x t warning (C0127) C0605 ü  ü ü

x020 OU MCTRL Overvoltage in the DC bus  ü ü

x030 LU MCTRL Undervoltage in the DC bus  ü ü

x032 LP1 MCTRL Motor phase failure C0597 ü ü  ü ü

x050 OH MCTRL Heat sink temperature higher than fixed limit

temperature

 ü ü

x051 OH1 MCTRL Temperature inside the controller > 90° C  ü

x053 OH3 MCTRL Motor temperature higher than fixed limit tem-

perature

C0583  ü ü ü

x054 OH4 MCTRL Heat sink temperature higher than variable li-

mit temperature (C0122)

C0582  ü ü ü

x055 OH5 MCTRL Temperature inside the controller > C0124 C0605 ü  ü ü

x057 OH7 MCTRL Motor temperature higher than variable limit

temperature (C0121)

C0584  ü ü ü

x058 OH8 MCTRL Motor temperature via inputs T1/T2 too high C0585 ü ü  ü ü

x061 CE0 AIF Communication error between AIF mo-

duleóPLC

C0126 ü ü  ü ü ü

CAN communication error:

x062 CE1 CAN1 CAN1_IN (monitoring time can be set under

C0357/1)

C0591

ü ü  ü ü ü

x063 CE2 CAN2 CAN2_IN (monitoring time can be set under

C0357/2)

C0592

x064 CE3 CAN3 CAN3_IN (monitoring time can be set under

C0357/3)

C0593

x065 CE4 CAN CAN BUS−OFF status

(too many faulty telegrams received)

C0595 ü ü  ü ü ü

x066 CE5 CAN CAN time−out (gateway function C0370) C0603 ü ü  ü ü ü

x070 U15 internal Undervoltage of internal 15 V voltage supply  ü ü ü

x071 CCr internal Internal error

 ü ü ü

x072 PR1 internal Check sum error in parameter set 1  ü ü ü

x074 PEr internal Program error

 ü ü ü

x075 PR0 internal General error in the parameter sets

 ü ü ü

x076 PR5 internal Error saving parameters  ü ü

x079 PI internal Error during parameter initialisation

 ü ü ü

x080 PR6 internal Too many user codes  ü ü ü

x082 Sd2 MCTRL Resolver error C0586  ü ü ü ü

x083 Sd3 MCTRL Encoder error at X9 PIN 8 C0587 ü ü  ü

x085 Sd5 MCTRL Encoder error at analog input (X6) (C0034 = 1) C0598 ü ü  ü ü

x086 Sd6 MCTRL Sensor error: motor temperature (X7 or X8) C0594  ü ü ü ü

x087 Sd7 MCTRL Absolute−value encoder error at X8

C0025  ü ü

x088 Sd8 MCTRL Absolute−value encoder error at X8

C0580 ü  ü ü

x: 0 = TRIP, 1 = Message, 2 = Warning, 3 = FAIL−QSP

After error correction: completely deenergise the device!

1 2 ... 83 84 85 86 87 88 89 90 91 92 93 ... 128 129

Commentaires sur ces manuels

Pas de commentaire

Lenze Global Drive PLC Developer Studio Manuel d'utilisateur Page 88

Commentaires sur ces manuels

Produits connexes et manuels pour Matériel Lenze Global Drive PLC Developer Studio