Lenze DDS System bus CAN for PLC Manuel d'utilisateur Page 117
- Page / 178
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
System bus (CAN) for Lenze PLC devices
FIF−CAN system blocks
8.1 FIF_CAN1_IO (node number: 34)
8−1
L
PLC−Systembus EN 2.0
8 FIF−CAN system blocks (only Drive PLC)
8.1 FIF_CAN1_IO (node number: 34)
This SB serves to the transmission of cyclic process data via the function interface of the Drive PLC.
· For the transmission a sync telegram is required, which has to be generated by a different
node.
(^ 2−9)
FIF_CAN1_nInW0_a
FIF_CAN1_nInW1_a
FIF_CAN1_bInB _b0...15
FIF_CAN1_bInB _b16...31
FIF System bus interface
Byte
7
8
5
6
3
4
1
2
Byte
7
8
5
6
3
4
1
2
FIF_CAN1_nOutW0_a
FIF_CAN1_nOutW1_a
FIF_CAN1_nOutW2_a
FIF_CAN1_bFDO _b16...31
FIF_CAN1_dnOutD1_p
FIF_CAN1_IO
DINT
WORD
WORD
WORD
16 x BOOL
DINT
Output user data
(8 bytes)
Input user data
(8 bytes)
L
H
L
H
FIF_CAN1_bFDO _b0...15
16 x BOOL
FIF_CAN1_nOutW3_a
WORD
FIF_CAN1_nInW2_a
FIF_CAN1_nInW3_a
FIF_CAN1_dnInD1_p
C2493/1
C2493/2
C2493/3
FIF_CAN1_bFDO _b32...47
16 x BOOL
FIF_CAN1_bFDO _b48...63
16 x BOOL
WORD
WORD
16 x BOOL
16 x BOOL
WORD
C2492/1
C2492/2
C2492/3
16 x BOOL
16 x BOOL
WORD
C2491/1
FIF_CAN1_bInB _b32...47
FIF_CAN1_bInB _b48...63
C2491/2
Fig. 8−1 FIF_CAN1_IO system block
- Global Drive 1
- System bus (CAN) 1
- Contents 4
- 1.1 About this Manual 9
- · "Via wDrvNr..." 10
- 1.1.4 Terminology used 12
- 2.1 Introduction 13
- General information 14
- 2.4.1 Identifier 15
- 2.4.2 User data 17
- 2.5 Network management (NMT) 18
- 2.6.1 Process data channels 19
- 2.6.3 Process data telegram 22
- 2.7.1 Parameter data telegram 23
- 2.7.1.1 Identifier 23
- 2.7.1.2 Command code 24
- 2.8 Free CAN objects 31
- 2.10 Monitoring mechanisms 33
- NMT Master NMT Slave 34
- 3.1 CAN baud rate 35
- 3.2 CAN boot−up 36
- 3.3 Node address (node ID) 37
- 3.7 Synchronisation 41
- 3.8 Reset node 42
- 3.9 System bus management 42
- 3.10 Mapping indexes to codes 42
- 3.12 Monitoring processes 45
- 3.13 Diagnostics 47
- 3.13.2 Telegram counter 48
- 3.13.3 Bus load by the PLC 49
- 4.1 CAN baud rate 51
- 4.2 CAN boot−up 52
- 4.3 Node address (node ID) 53
- Configuration (AIF interface) 54
- 4.6 Synchronisation 57
- 4.7 Reset node 58
- 4.8 Monitoring processes 58
- 4.8.2 Bus off 59
- 4.9 Diagnostics 60
- 5.1 CAN baud rate 61
- 5.2 CAN boot−up 62
- 5.3 Node address (node ID) 63
- Configuration (FIF interface) 64
- 5.7 Synchronisation 67
- 5.8 Reset node 68
- 5.9 System bus management 68
- 5.10 Monitoring processes 69
- 5.11 Diagnostics 71
- 5.11.2 Telegram counter 72
- 5.11.3 Bus load by FIF−CAN 73
- 6.1 CAN baud rate 75
- 6.2 CAN boot−up 76
- 6.3 Node address (Node ID) 77
- 6.7 Synchronisation 81
- 6.8 Reset node 82
- 6.9 System bus management 82
- 6.10 Monitoring processes 83
- 6.11 Diagnostics 85
- 6.11.2 Telegram counter 86
- 6.11.3 Bus load by CAN−AUX 87
- 7 CAN system blocks 89
- 7.1.1 Inputs_CAN1 90
- 7.1.2 Outputs_CAN1 90
- 7.1.3 Process data telegram 91
- 7.2.1 Inputs_CAN1 95
- 7.2.2 Outputs_CAN1 95
- 7.2.3 Process data telegram 96
- 7.3.1 Inputs_CAN1 99
- 7.3.2 Outputs_CAN1 99
- CAN system blocks 100
- 7.3.3 Process data telegram 100
- 7.4 CAN2_IO (node number: 32) 102
- 7.4.1 Inputs_CAN2 103
- 7.4.2 Outputs_CAN2 103
- 7.4.3 Process data telegram 103
- 7.5 CAN3_IO (node number: 33) 105
- 7.5.1 Inputs_CAN3 106
- 7.5.2 Outputs_CAN3 106
- 7.5.3 Process data telegram 106
- 7.6.1 Inputs_CAN_Management 108
- PLC−Systembus EN 2.0 109
- 7.6.5 Status messages 110
- FIF−CAN system blocks 117
- 8.1.1 FIF_Inputs_CAN1 118
- 8.1.2 FIF_Outputs_CAN1 118
- 8.1.3 Process data telegram 119
- 8.2.1 FIF_Inputs_CAN2 122
- 8.2.2 FIF_Outputs_CAN2 122
- 8.2.3 Process data telegram 122
- 8.3.1 FIF_Inputs_CAN3 125
- 8.3.2 FIF_Outputs_CAN3 125
- 8.3.3 Process data telegram 125
- 8.4.5 Status messages 129
- CAN−AUX system blocks 130
- 9.1.1 Inputs_CANaux1 131
- 9.1.2 Outputs_CANaux1 131
- 9.1.3 Process data telegram 132
- 9.2.1 Inputs_CANaux2 135
- 9.2.2 Outputs_CANaux2 135
- 9.2.3 Process data telegram 135
- 9.3.1 Inputs_CANaux3 138
- 9.3.2 Outputs_CANaux3 138
- 9.3.3 Process data telegram 138
- 9.4.5 Status messages 142
- 10.1 Overview 143
- L_CanInit 144
- · Not for Drive PLC! 146
- Transmit status (nState) 151
- · See the following table 154
- 11.1 Overview 157
- · Invalid for bit 0 = 1 161
- L_CanDSxHeartBeat 164
- L_CanDSxNodeGuarding 168
- NodeLifeTimeFactor (C0383) 170
- Guarding" 171
- L PLC−Systembus EN 2.0 173
- 12 Index 173
- XCAN sync identifier, 4−7 178
- XCAN sync response, 4−7 178
Produits connexes et manuels pour Matériel Lenze DDS System bus CAN for PLC
Matériel Lenze 931K Manuel d'utilisateur
(148 pages)
(148 pages)
Matériel Lenze MDFQA Manuel d'utilisateur
(32 pages)
(32 pages)
Matériel Lenze DDS v2.1 Manuel d'utilisateur
(41 pages)
(41 pages)
Matériel Lenze E82ZWBRU Manuel d'utilisateur
(63 pages)
(63 pages)
Matériel Lenze 8615E Manuel d'utilisateur
(126 pages)
(126 pages)
Matériel Lenze E94P Manuel d'utilisateur
(1 pages)
(1 pages)
Matériel Lenze E82ZBU Manuel d'utilisateur
(18 pages)
(18 pages)
Matériel Lenze DDS v2.0 Manuel d'utilisateur
(26 pages)
(26 pages)
Matériel Lenze DDS v2.3 Manuel d'utilisateur
(340 pages)
(340 pages)
Matériel Lenze 8615E Manuel d'utilisateur
(158 pages)
(158 pages)
Matériel Lenze E82ZBC Manuel d'utilisateur
(102 pages)
(102 pages)
Matériel Lenze DDS v1.1 Manuel d'utilisateur
(11 pages)
(11 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.039 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels