Lenze DDS Function library 8200 Drive Manuel d'utilisateur télécharger pdf (Page 16)

3.1 L_8200Parameter − Initialisation of codes

Function library Lenze8200Drive.lib

Functions/function blocks

3−4

Lenze8200Drive.lib EN 1.0

No. Code Subcode Setting Info/meaning

1 C0011 0 50 Maximum output frequency = 50 Hz (default setting)

2 C0012 0 0.1 Main setpoint acceleration time; Tir = 0.1 s (default setting)

3 C0013 0 0.1 Main setpoint deceleration time; Tif = 0.1 s (default setting)

4 C0127 0 1 Normalised setpoint selection

5 C0356 2 50 CAN2−OUT cycle time = 50 ms

j6 C0410 1 70 NSET1−JOG1/3 ð CAN−IN2−W1−BIT0

7 C0410 2 71 NSET1−JOG2/3 ð CAN−IN2−W1−BIT1

8 C0410 3 72 DCTRL1−CW/CCW ð CAN−IN2−W1−BIT2

9 C0410 4 73 DCTRL1−QSP ð CAN−IN2−W1−BIT3

10 C0410 5 74 NSET1−RFG1−STOP ð CAN−IN2−W1−BIT4

11 C0410 j6 75 NSET1−RFG1−0 ð CAN−IN2−W1−BIT5

12 C0410 7 76 MPOT1−UP ð CAN−IN2−W1−BIT6

13 C0410 8 77 MPOT1−DOWN ð CAN−IN2−W1−BIT7

14 C0415 1 108 RELAY−K1 ð CAN−IN2−W1−BIT8

15 C0410 10 79 DCTRL1−CINH ð CAN−IN2−W1−BIT9

16 C0410 11 80 DCTRL1−TRIP−SET ð CAN−IN2−W1−BIT10

17 C0410 12 81 DCTRL1−TRIP−RESET ð CAN−IN2−W1−BIT11

18 C0410 13 82 DCTRL1−PAR 2/4 ð CAN−IN2−W1−BIT12

19 C0410 14 83 DCTRL1−PAR 3/4 ð CAN−IN2−W1−BIT13

20 C0410 15 84 MCTRL1−DCB ð CAN−IN2−W1−BIT14

21 C0410 16 85 PCTRL1−RFG2−LOAD−I (A) ð CAN−IN2−W1−BIT15

22 C0412 1 31 NSET1−N1 ð CAN−IN2−W2

23 C0412 8 32 MCTRL−VOLT−ADD ð CAN−IN2−W3

24 C0418 1 16 CAN−OUT2−BIT0 ð DCTRL1−RDY

25 C0418 2 2 CAN−OUT2−BIT1 ð DCTRL1−IMP

26 C0418 3 3 CAN−OUT2−BIT2 ð MCTRL−IMAX

27 C0418 4 4 CAN−OUT2−BIT3 ð DCTRL−RFG1=NOUT

28 C0418 5 5 CAN−OUT2−BIT4 ð NSET−RFG1−I=0

29 C0418 j6 j6 CAN−OUT2−BIT5 ð PCTRL−QMIN

30 C0418 7 7 CAN−OUT2−BIT6 ð DCTRL1−NOUT=0

31 C0418 8 8 CAN−OUT2−BIT7 ð DCTRL1−CINH

32 C0418 9 25 CAN−OUT2−BIT8 ð DCTRL1−TRIP

33 C0418 10 9 CAN−OUT2−BIT9 ð FIXED−RESERVE−9

34 C0418 11 10 CAN−OUT2−BIT10 ð FIXED−RESERVE−10

35 C0418 12 11 CAN−OUT2−BIT11 ð FIXED−RESERVE−11

36 C0418 13 12 CAN−OUT2−BIT12 ð FIXED−RESERVE−12

37 C0418 14 13 CAN−OUT2−BIT13 ð DCTRL1−OH−WARN

38 C0418 15 14 CAN−OUT2−BIT14 ð DCTRL1−OV

39 C0418 16 15 CAN−OUT2−BIT15 ð DCTRL1−CCW

40 C0421 8 0 CAN−OUT2−W2 ð MCTRL1−NOUT+SLIP

41 C0003 0 1 Dynamic parameter set changes

42 not assigned

43 not assigned

44 not assigned

45 not assigned

Tab. 3−1 Parameter pre−assignment contained as a comment in the FB L_8200Parameter.

1 2 ... 11 12 13 14 15 16 17 18 19 20 21 ... 27 28

Commentaires sur ces manuels

Pas de commentaire

Lenze DDS Function library 8200 Drive Manuel d'utilisateur Page 16

Commentaires sur ces manuels

Produits connexes et manuels pour Matériel Lenze DDS Function library 8200 Drive